Fritz Handle Sword Walking Cane With Black Aluminum Shaft free S&H*

Fritz Handle Sword Walking Cane With Black Aluminum Shaft

Heavy Duty Sword Cane 37.5 Inches. Aluminum Shaft Our design concept for the Heavy Sword Cane was to make a cane that offered significant orthopedic support, and be stylish enough so that it didn't look like a stodgy piece of medical equipment. The result is a very appealing cane with an extra strong partial crook handle made from Grivory, with a black, aluminum shaft that's 2mm thick and heat-treated for strength. The shaft is handsomely tapered and capped with a thick rubber ferrule for better traction on slick, icy sidewalks or uneven terrain. The concealed sword is easily released by a hard, quick tug on the handle to break the suction of its friction lock. It's an extremely formidable sword too, made from 1055 Carbon steel, a little over 24in length and 5.5mm thick. It's sturdy enough for both cutting and thrusting, with one long cutting edge, a strong sharp point, and a fully sharpened back edge. It's more than enough to take down any attacker, and the heavy aluminum shaft of your cane makes a fine weak hand parrying weapon and a frightfully effective bludgeon in its own right.

• This cane is designed for users up to 180lbs.

• The Tip size on this cane is 18mm. This cane does come with 1 complementary tip on the cane. If you need an extra tip please go Here.
  

• The approximate weight of this item is 2.15lbs.
  

Size Chart

The "Standard Size" for this cane is 37 Inches. This is the maximum length that this cane is manufactured.
(You may choose to have the cane shortened if the "Optional Sizing" option is available under the "Add to Cart" button.)

To check to see if the size adjustment above will fit the cane user please use the information below to determine the users size*.

(If the adjustment range will not fit the user please call to place your order. We may be able to cut down the cane to make it adjust in size in a shorter height. Canes cut from their original size will incur a 30% restocking fee if returned)

Choose 1 of 3 easy ways to determine cane length.

1. Measure the size of an existing cane.
   Do this method by simply measuring from the lowest part on the top of the handle to the bottom of the rubber tip. Round up to the nearest half inch. (see Diagram Above)
2. Measure the cane user
   1. Put on the user's walking shoes.
   2. Have the user stand naturally upright as much as possible.
   3. Have their arms fall to the sides naturally with a normal relaxed bend at the elbow. (Please see Diagram Above for correct posture)
   4. Using a tape measure or yard stick, measure the distance from their wrist joint (bottom crease at the wrist) down to the floor. Round up to the nearest half inch.
      (**For accurate length a second person must read measurement to prevent wrist from moving)
3. Measure half the height in inches. (Only use if Step 1 or 2 are not available as options)
   (Although this works for most cane users it is not always exact. Choose this option at your
   own risk a 30% restocking fee applies to all returned cut canes)
   Most users cane measurements will be within one inch of half the users height.
   1. Convert height into inches...(example 66 Inches) then divide in half = 33 inches.
      (round up to the nearest half inch.)
   2. Then add half an inch to this height.
   3. After receiving product use step #2 to confirm and change size if needed.

The Estimated height would be 33.5 inches for this example.

*PLEASE NOTE: THIS INFORMATION IN NO WAY REPLACES A MEDICAL PROFESSIONAL'S RECOMMENDATION. CANES ARE NOT INTENDED TO BE USED LIKE A CRUTCH FOR FULL WEIGHT SUPPORT, CANES ARE INTENDED ONLY FOR BALANCE.
The sizing information above is the standard measurement for a walking cane. Some users may require a special length. As with any mobility device please see you doctor before sizing and use. Varying heel height of different shoes may change users size.
Sizing is a free courtesy. In most cases, sized canes will ship the same day. In rare cases sizing requests may not or cannot be sized. In these rare situations "pick up" call tags will not be issued and the item must be sent back to us to be sized. We will not ship out a new product. Please always check the item upon delivery to confirm the requested size. Canes can always be shortened but may not be lengthened.

Product Reviews

Engraving

Engraving is now available! Genuine Brass or Anodized Aluminum plaques are engraved and bent to the curve of the shaft of the cane. Please click on the images below to see more details.... (PLEASE NOTE - Engraving does not apply towards the $60 to recieve free shipping)